IONIQ ELECTRICAL – LEAK TESTER FOR HIGH VOLUME PLASTIC PART PRODUCTION OR BATTERY CELL LEAK TESTING
New! Leak Tester for High Volume Production or Battery Leak Testing

On the basis of its well-proven concept of production line Quality Control Testers, ATEQ has developed a new leak Tester, designed for the specific requirements of high volume production of plastic parts or battery cell leak testing. This instrument is used for the detection of localized molding faults, insufficient membrane thickness, perforations, etc…. The IONIQ 20 is based on discharge current measurement and is able to detect defects in the region of 10μm.
The Ioniq is perfect for leak testing battery cells. For the light PC-controlled version of the Ioniq, see battery cell leak testerATEQ’s B28 electrical leak tester.
1 to 3 Simultaneous Test Channels
Display 1 to 3 Channels
For Industrial Line and Laboratory
If your application requires 6 simultaneous test channels, ATEQ recommends the IONIQ 6SW  operator safety.

CONTACT US

IONIQ ELECTRICAL : APPLICATIONS

  • The Ioniq system is ideal for high volume tests on bottle caps for injection point defects, on plastic or insulating membranes for thickness defects.
  • The Ioniq is perfect for leak testing battery cells.  For the light PC-controlled version of the Ioniq, see ATEQ’s B28 electrical leak tester.

IONIQ ELECTRICAL : MEASUREMENT PRINCIPLE

• The IONIQ measures the current flowing between a patented charged probe and a ground plate placed under the part to be tested.

• The IONIQ uses the % of the nominal voltage (which reflects the discharge current), measured on the part as PASS/FAIL level.

• In a PASS situation (fig 1) : No hole, no weak part, the IONIQ measures a high %. The measured voltage and the nominal voltage are virtually equal. The result is above the reject level, the part has passed the test.

• In a FAIL situation (fig 2) : The IONIQ measures a low %. The measured voltage is significantly below the nominal voltage. The result is below the reject level, the part has failed the test.

• Test limitations: short probe-part-plate distance, electrical insulation from environment.

IONIQ ELECTRICAL : FEATURES

  • Integrated ionizing high voltage generator
    (5 to 27.3 kV)
  • Reject levels as % of nominal voltage
    (0 to 100%)
  • Monitoring and protection of high voltage generator.
  • Limitation of the current rating
  • Speed: Minimum cycle time 0.6s
  • I/O’s for instrument control and results
  • 32 programs
  • Remote control allows the test module to be close to the test part
  • Language selection, customization of test

IONIQ ELECTRICAL : SPECIFICATIONS

  • HIGH VOLTAGE GENERATOR

    • Integrated and adjustable according to application (5 to 27.3 kV)
  • TEMPERATURE

    • Operating : + 50°F to + 113°F
    • Storage : 32°F to + 140°F
  • POWER SUPPLY

    • 24 VDC/ 1A
      Note: It is vital that the instrument has a good ground connection.
  • OPTIONAL

    • Save results module
    • Standard resistor box with 2 values
  • INTERFACE
    Programming via remote control 7 inputs / 5 outputs for PLC controlled applications. Inputs:

    • Inputs : Optically isolated.
      24 V – 10 mA maximum or dry contact.
    • Outputs : Relay output
      Rated 48 V / 200 mA maximum.
  • DIMENSIONS

    • Box dimensions :
      Dimensions : H x L x P = 136 x 250 x 255 mm
      Weight : 8 kg
    • Remote control :
      Dimensions : H x L x P = 250 x 250 x 60 mm
      Weight : 2.8 kg

IONIQ ELECTRICAL : FACTSHEETS

Detailed information about the IONIQ ELECTRICAL including features, specifications, etc.

IONIQ ELECTRICAL : TECHNOLOGY

A high voltage loaded sharp end is applied next to an earth connected base and in between lays the plastic part we test. Should a hole exist in the part, ions will start moving from the earth to the sharp end. This will result in a loss of power and be translated into a leak.
While this method does not quantify the leak rate in terms of cc/min for example, it is the fastest ever invented to detect a leak in a go / no go process.
We have achieved cycle times of less than 7/10 of a second.

Leak Ranges: Depends on the size of the hole and the material of the part
Accuracy: Depends on the size of the hole and the material of the part