IONIQ 6SW

HIGH VOLUME PRODUCTION BATTERY POUCH CELL TESTING

On the basis of its well proven concept of production line QC Testers, ATEQ has developed a new leak tester designed for the specific requirements of high volume production of plastic parts. This instrument is used for the detection of localized molding faults, insufficient membrane thickness, perforations, etc. This instrument has also proven to be effective on testing pouch battery cells.

IONIQ 20 – 1 to 3 Channel Electrical Tester

The IONIQ is based on discharge current measurement and is able to detect defects up to of 10µm.

APPLICATION

EMOBILITY
- Pouches & Cells
- Modules

PACKAGINGS
- Aerosol Caps
- Plastic Bags
- Sprays
- Plastic Bottles...

MEDICAL
- Blister Packs
- Fluid Bags
- Filters
- Condoms…

FEATURES

GENERAL
- Integrated ionizing high voltage generator
- Integrated and adjustable according toapplication (5 to 27.3 kV)
- Reject levels as % of nominal voltage (0 to 100%)
- Monitoring and protection of high voltage generator
- Limitation of the current rating
- Speed: Minimum cycle time 0.6s
- I/O’s for instrument control and results
- 32 programs
- Measuring box and remote control
- Timestamp, language selection, test customization

SPECIFICATIONS

TEMPERATURE
- Operating : + 10°C at + 45°C
- Storage : 0°C at + 60°C
POWER SUPPLY
- 90 V to 240 V AC
- Single phase : 50/60 Hz – 45 W
- Note : The instrument needs a good ground connection
OPTIONAL
- Save results module
- Standard resistor box with 2 values

INTERFACE
Programming via remote control 7 inputs / 5 outputs for PLC controlled applications.
- Inputs : Optically isolated.
  24 V – 10 mA maximum or dry contact.
- Outputs : Relay output
  Rated 48 V / 200 mA maximum.
DIMENSIONS
- Instrument : Dimensions : H x L x P = 350 x 200 x 250 mm
  Weight : 9.4 kg
- Remote control : Dimensions : H x L x P = 250 x 250 x 60 mm
- Weight : 2.8 kg

MEASUREMENT PRINCIPLE

The IONIQ measures the current flowing between a patented charged probe and a ground plate placed under the part to be tested.
The IONIQ uses the % of the nominal voltage (which reflects the discharge current), measured on the part as PASS/FAIL level.
In a PASS situation (fig 1) : No hole, no weak part, the IONIQ measures a high %. The measured voltage and the nominal voltage are virtually equal. The result is above the reject level, the part has passed the test.
In a FAIL situation (fig 2) : The IONIQ measures a low %. The measured voltage is significantly below the nominal voltage. The result is below the reject level, the part has failed the test.
Test limitations: short probe-part-plate distance, electrical insulation from environment.

Diagram showing how the ATEQ IONIQ 6SW works with a good part

Diagram showing how the ATEQ IONIQ 6SW works with a bad part

TECHNOLOGY

A high voltage loaded sharp end is applied next to an earth connected base and in between lays the plastic part we test. Should a hole exist in the part, ions will start moving from the earth to the sharp end. This will result in a loss of power and be translated into a leak.

While this method does not quantify the leak rate in terms of cc/min for example, it is the fastest ever invented to detect a leak in a go / no go process.

We have achieved cycle times of less than 7/10 of a second.

Leak Ranges: Depends on the size of the hole and the material of the part

Accuracy: Depends on the size of the hole and the material of the part

DOCUMENTATION

IONIQ 6SW

DATASHEETS

USER MANUAL

Sales and Applications

Product Support

Locations Map

Repair and Calibration